No ethernet ip address in my vocore2
0
I just flashed my vocore2u with openwrt 18.06.1, and plug it with an ethernet cable to access network while setting up wireless access-point for my phone.
The AP is working and connected to the network, but the ip in my phone is in the subnet of another router. And there's no ip assigned to my vocore2 so I cannot ssh into it. After connecting to vocore2 with serial terminal, ping 8.8.8.8 is also failed.
How can I make my vocore2 gain ip from the router and setting up the network well?
root@OpenWrt:/etc/config# ifconfig
apcli0 Link encap:Ethernet HWaddr BA:D8:12:07:01:71
inet6 addr: fe80::b8d8:12ff:fe07:171/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
br-lan Link encap:Ethernet HWaddr B8:D8:12:67:01:72
inet addr:192.168.61.1 Bcast:192.168.61.255 Mask:255.255.255.0
inet6 addr: fd43:4277:1a20::1/60 Scope:Global
inet6 addr: fe80::bad8:12ff:fe67:172/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:16891 errors:0 dropped:0 overruns:0 frame:0
TX packets:2404 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:1181826 (1.1 MiB) TX bytes:477837 (466.6 KiB)
eth0 Link encap:Ethernet HWaddr B8:D8:12:67:01:72
inet6 addr: fe80::bad8:12ff:fe67:172/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:2773 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:736242 (718.9 KiB)
Interrupt:5
eth0.1 Link encap:Ethernet HWaddr B8:D8:12:67:01:72
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:1067 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:145725 (142.3 KiB)
eth0.2 Link encap:Ethernet HWaddr B8:D8:12:67:01:72
inet6 addr: fe80::bad8:12ff:fe67:172/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:1692 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:577096 (563.5 KiB)
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:65536 Metric:1
RX packets:886 errors:0 dropped:0 overruns:0 frame:0
TX packets:886 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:64988 (63.4 KiB) TX bytes:64988 (63.4 KiB)
ra0 Link encap:Ethernet HWaddr B8:D8:12:67:01:71
inet6 addr: fe80::bad8:12ff:fe67:171/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:27199 errors:14 dropped:0 overruns:0 frame:0
TX packets:2398 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:2189856 (2.0 MiB) TX bytes:441570 (431.2 KiB)
Interrupt:6
network config
root@OpenWrt:/etc/config# uci show network
network.loopback=interface
network.loopback.ifname='lo'
network.loopback.proto='static'
network.loopback.ipaddr='127.0.0.1'
network.loopback.netmask='255.0.0.0'
network.globals=globals
network.globals.ula_prefix='fd43:4277:1a20::/48'
network.lan=interface
network.lan.type='bridge'
network.lan.ifname='eth0.1'
network.lan.proto='static'
network.lan.ipaddr='192.168.61.1'
network.lan.netmask='255.255.255.0'
network.lan.ip6assign='60'
network.lan_dev=device
network.lan_dev.name='eth0.1'
network.lan_dev.macaddr='b8:d8:12:67:01:72'
network.wan=interface
network.wan.ifname='eth0.2'
network.wan.force_link='1'
network.wan.proto='dhcp'
network.wwan=interface
network.wwan.ifname='apcli0'
network.wwan.proto='dhcp'
network.@switch[0]=switch
network.@switch[0].name='switch0'
network.@switch[0].reset='1'
network.@switch[0].enable_vlan='1'
network.@switch_vlan[0]=switch_vlan
network.@switch_vlan[0].device='switch0'
network.@switch_vlan[0].vlan='1'
network.@switch_vlan[0].ports='0 2 6t'
bridge openwrt
asked 12 mins ago
artificerpiartificerpi
1013
add a comment |
0
I just flashed my vocore2u with openwrt 18.06.1, and plug it with an ethernet cable to access network while setting up wireless access-point for my phone.
The AP is working and connected to the network, but the ip in my phone is in the subnet of another router. And there's no ip assigned to my vocore2 so I cannot ssh into it. After connecting to vocore2 with serial terminal, ping 8.8.8.8 is also failed.
How can I make my vocore2 gain ip from the router and setting up the network well?
root@OpenWrt:/etc/config# ifconfig
apcli0 Link encap:Ethernet HWaddr BA:D8:12:07:01:71
inet6 addr: fe80::b8d8:12ff:fe07:171/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
br-lan Link encap:Ethernet HWaddr B8:D8:12:67:01:72
inet addr:192.168.61.1 Bcast:192.168.61.255 Mask:255.255.255.0
inet6 addr: fd43:4277:1a20::1/60 Scope:Global
inet6 addr: fe80::bad8:12ff:fe67:172/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:16891 errors:0 dropped:0 overruns:0 frame:0
TX packets:2404 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:1181826 (1.1 MiB) TX bytes:477837 (466.6 KiB)
eth0 Link encap:Ethernet HWaddr B8:D8:12:67:01:72
inet6 addr: fe80::bad8:12ff:fe67:172/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:2773 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:736242 (718.9 KiB)
Interrupt:5
eth0.1 Link encap:Ethernet HWaddr B8:D8:12:67:01:72
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:1067 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:145725 (142.3 KiB)
eth0.2 Link encap:Ethernet HWaddr B8:D8:12:67:01:72
inet6 addr: fe80::bad8:12ff:fe67:172/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:1692 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:577096 (563.5 KiB)
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:65536 Metric:1
RX packets:886 errors:0 dropped:0 overruns:0 frame:0
TX packets:886 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:64988 (63.4 KiB) TX bytes:64988 (63.4 KiB)
ra0 Link encap:Ethernet HWaddr B8:D8:12:67:01:71
inet6 addr: fe80::bad8:12ff:fe67:171/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:27199 errors:14 dropped:0 overruns:0 frame:0
TX packets:2398 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:2189856 (2.0 MiB) TX bytes:441570 (431.2 KiB)
Interrupt:6
network config
root@OpenWrt:/etc/config# uci show network
network.loopback=interface
network.loopback.ifname='lo'
network.loopback.proto='static'
network.loopback.ipaddr='127.0.0.1'
network.loopback.netmask='255.0.0.0'
network.globals=globals
network.globals.ula_prefix='fd43:4277:1a20::/48'
network.lan=interface
network.lan.type='bridge'
network.lan.ifname='eth0.1'
network.lan.proto='static'
network.lan.ipaddr='192.168.61.1'
network.lan.netmask='255.255.255.0'
network.lan.ip6assign='60'
network.lan_dev=device
network.lan_dev.name='eth0.1'
network.lan_dev.macaddr='b8:d8:12:67:01:72'
network.wan=interface
network.wan.ifname='eth0.2'
network.wan.force_link='1'
network.wan.proto='dhcp'
network.wwan=interface
network.wwan.ifname='apcli0'
network.wwan.proto='dhcp'
network.@switch[0]=switch
network.@switch[0].name='switch0'
network.@switch[0].reset='1'
network.@switch[0].enable_vlan='1'
network.@switch_vlan[0]=switch_vlan
network.@switch_vlan[0].device='switch0'
network.@switch_vlan[0].vlan='1'
network.@switch_vlan[0].ports='0 2 6t'
bridge openwrt
asked 12 mins ago
artificerpiartificerpi
1013
add a comment |
0
0
0
I just flashed my vocore2u with openwrt 18.06.1, and plug it with an ethernet cable to access network while setting up wireless access-point for my phone.
The AP is working and connected to the network, but the ip in my phone is in the subnet of another router. And there's no ip assigned to my vocore2 so I cannot ssh into it. After connecting to vocore2 with serial terminal, ping 8.8.8.8 is also failed.
How can I make my vocore2 gain ip from the router and setting up the network well?
root@OpenWrt:/etc/config# ifconfig
apcli0 Link encap:Ethernet HWaddr BA:D8:12:07:01:71
inet6 addr: fe80::b8d8:12ff:fe07:171/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
br-lan Link encap:Ethernet HWaddr B8:D8:12:67:01:72
inet addr:192.168.61.1 Bcast:192.168.61.255 Mask:255.255.255.0
inet6 addr: fd43:4277:1a20::1/60 Scope:Global
inet6 addr: fe80::bad8:12ff:fe67:172/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:16891 errors:0 dropped:0 overruns:0 frame:0
TX packets:2404 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:1181826 (1.1 MiB) TX bytes:477837 (466.6 KiB)
eth0 Link encap:Ethernet HWaddr B8:D8:12:67:01:72
inet6 addr: fe80::bad8:12ff:fe67:172/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:2773 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:736242 (718.9 KiB)
Interrupt:5
eth0.1 Link encap:Ethernet HWaddr B8:D8:12:67:01:72
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:1067 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:145725 (142.3 KiB)
eth0.2 Link encap:Ethernet HWaddr B8:D8:12:67:01:72
inet6 addr: fe80::bad8:12ff:fe67:172/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:1692 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:577096 (563.5 KiB)
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:65536 Metric:1
RX packets:886 errors:0 dropped:0 overruns:0 frame:0
TX packets:886 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:64988 (63.4 KiB) TX bytes:64988 (63.4 KiB)
ra0 Link encap:Ethernet HWaddr B8:D8:12:67:01:71
inet6 addr: fe80::bad8:12ff:fe67:171/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:27199 errors:14 dropped:0 overruns:0 frame:0
TX packets:2398 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:2189856 (2.0 MiB) TX bytes:441570 (431.2 KiB)
Interrupt:6
network config
root@OpenWrt:/etc/config# uci show network
network.loopback=interface
network.loopback.ifname='lo'
network.loopback.proto='static'
network.loopback.ipaddr='127.0.0.1'
network.loopback.netmask='255.0.0.0'
network.globals=globals
network.globals.ula_prefix='fd43:4277:1a20::/48'
network.lan=interface
network.lan.type='bridge'
network.lan.ifname='eth0.1'
network.lan.proto='static'
network.lan.ipaddr='192.168.61.1'
network.lan.netmask='255.255.255.0'
network.lan.ip6assign='60'
network.lan_dev=device
network.lan_dev.name='eth0.1'
network.lan_dev.macaddr='b8:d8:12:67:01:72'
network.wan=interface
network.wan.ifname='eth0.2'
network.wan.force_link='1'
network.wan.proto='dhcp'
network.wwan=interface
network.wwan.ifname='apcli0'
network.wwan.proto='dhcp'
network.@switch[0]=switch
network.@switch[0].name='switch0'
network.@switch[0].reset='1'
network.@switch[0].enable_vlan='1'
network.@switch_vlan[0]=switch_vlan
network.@switch_vlan[0].device='switch0'
network.@switch_vlan[0].vlan='1'
network.@switch_vlan[0].ports='0 2 6t'
bridge openwrt
asked 12 mins ago
artificerpiartificerpi
1013
I just flashed my vocore2u with openwrt 18.06.1, and plug it with an ethernet cable to access network while setting up wireless access-point for my phone.
The AP is working and connected to the network, but the ip in my phone is in the subnet of another router. And there's no ip assigned to my vocore2 so I cannot ssh into it. After connecting to vocore2 with serial terminal, ping 8.8.8.8 is also failed.
How can I make my vocore2 gain ip from the router and setting up the network well?
root@OpenWrt:/etc/config# ifconfig
apcli0 Link encap:Ethernet HWaddr BA:D8:12:07:01:71
inet6 addr: fe80::b8d8:12ff:fe07:171/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
br-lan Link encap:Ethernet HWaddr B8:D8:12:67:01:72
inet addr:192.168.61.1 Bcast:192.168.61.255 Mask:255.255.255.0
inet6 addr: fd43:4277:1a20::1/60 Scope:Global
inet6 addr: fe80::bad8:12ff:fe67:172/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:16891 errors:0 dropped:0 overruns:0 frame:0
TX packets:2404 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:1181826 (1.1 MiB) TX bytes:477837 (466.6 KiB)
eth0 Link encap:Ethernet HWaddr B8:D8:12:67:01:72
inet6 addr: fe80::bad8:12ff:fe67:172/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:2773 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:736242 (718.9 KiB)
Interrupt:5
eth0.1 Link encap:Ethernet HWaddr B8:D8:12:67:01:72
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:1067 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:145725 (142.3 KiB)
eth0.2 Link encap:Ethernet HWaddr B8:D8:12:67:01:72
inet6 addr: fe80::bad8:12ff:fe67:172/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:1692 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:577096 (563.5 KiB)
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:65536 Metric:1
RX packets:886 errors:0 dropped:0 overruns:0 frame:0
TX packets:886 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:64988 (63.4 KiB) TX bytes:64988 (63.4 KiB)
ra0 Link encap:Ethernet HWaddr B8:D8:12:67:01:71
inet6 addr: fe80::bad8:12ff:fe67:171/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:27199 errors:14 dropped:0 overruns:0 frame:0
TX packets:2398 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:2189856 (2.0 MiB) TX bytes:441570 (431.2 KiB)
Interrupt:6
network config
root@OpenWrt:/etc/config# uci show network
network.loopback=interface
network.loopback.ifname='lo'
network.loopback.proto='static'
network.loopback.ipaddr='127.0.0.1'
network.loopback.netmask='255.0.0.0'
network.globals=globals
network.globals.ula_prefix='fd43:4277:1a20::/48'
network.lan=interface
network.lan.type='bridge'
network.lan.ifname='eth0.1'
network.lan.proto='static'
network.lan.ipaddr='192.168.61.1'
network.lan.netmask='255.255.255.0'
network.lan.ip6assign='60'
network.lan_dev=device
network.lan_dev.name='eth0.1'
network.lan_dev.macaddr='b8:d8:12:67:01:72'
network.wan=interface
network.wan.ifname='eth0.2'
network.wan.force_link='1'
network.wan.proto='dhcp'
network.wwan=interface
network.wwan.ifname='apcli0'
network.wwan.proto='dhcp'
network.@switch[0]=switch
network.@switch[0].name='switch0'
network.@switch[0].reset='1'
network.@switch[0].enable_vlan='1'
network.@switch_vlan[0]=switch_vlan
network.@switch_vlan[0].device='switch0'
network.@switch_vlan[0].vlan='1'
network.@switch_vlan[0].ports='0 2 6t'
bridge openwrt
bridge openwrt
asked 12 mins ago
artificerpiartificerpi
1013
asked 12 mins ago
artificerpiartificerpi
1013
edited 6 mins ago
artificerpi
asked 12 mins ago
artificerpiartificerpi
1013
asked 12 mins ago
artificerpiartificerpi
1013
asked 12 mins ago
artificerpiartificerpi
1013
1013
add a comment |
add a comment |
0
active
oldest
votes
Your Answer
StackExchange.ready(function() {
var channelOptions = {
tags: "".split(" "),
id: "106"
};
initTagRenderer("".split(" "), "".split(" "), channelOptions);
StackExchange.using("externalEditor", function() {
// Have to fire editor after snippets, if snippets enabled
if (StackExchange.settings.snippets.snippetsEnabled) {
StackExchange.using("snippets", function() {
createEditor();
});
}
else {
createEditor();
}
});
function createEditor() {
StackExchange.prepareEditor({
heartbeatType: 'answer',
autoActivateHeartbeat: false,
convertImagesToLinks: false,
noModals: true,
showLowRepImageUploadWarning: true,
reputationToPostImages: null,
bindNavPrevention: true,
postfix: "",
imageUploader: {
brandingHtml: "Powered by u003ca class="icon-imgur-white" href="https://imgur.com/"u003eu003c/au003e",
contentPolicyHtml: "User contributions licensed under u003ca href="https://creativecommons.org/licenses/by-sa/3.0/"u003ecc by-sa 3.0 with attribution requiredu003c/au003e u003ca href="https://stackoverflow.com/legal/content-policy"u003e(content policy)u003c/au003e",
allowUrls: true
},
onDemand: true,
discardSelector: ".discard-answer"
,immediatelyShowMarkdownHelp:true
});
}
});
draft saved
draft discarded
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
StackExchange.ready(
function () {
StackExchange.openid.initPostLogin('.new-post-login', 'https%3a%2f%2funix.stackexchange.com%2fquestions%2f493378%2fno-ethernet-ip-address-in-my-vocore2%23new-answer', 'question_page');
}
);
Post as a guest
Required, but never shown
0
active
oldest
votes
0
active
oldest
votes
active
oldest
votes
active
oldest
votes
draft saved
draft discarded
Thanks for contributing an answer to Unix & Linux Stack Exchange!
- Please be sure to answer the question. Provide details and share your research!
But avoid …
- Asking for help, clarification, or responding to other answers.
- Making statements based on opinion; back them up with references or personal experience.
To learn more, see our tips on writing great answers.
Some of your past answers have not been well-received, and you're in danger of being blocked from answering.
Please pay close attention to the following guidance:
- Please be sure to answer the question. Provide details and share your research!
But avoid …
- Asking for help, clarification, or responding to other answers.
- Making statements based on opinion; back them up with references or personal experience.
To learn more, see our tips on writing great answers.
draft saved
draft discarded
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
StackExchange.ready(
function () {
StackExchange.openid.initPostLogin('.new-post-login', 'https%3a%2f%2funix.stackexchange.com%2fquestions%2f493378%2fno-ethernet-ip-address-in-my-vocore2%23new-answer', 'question_page');
}
);
Post as a guest
Required, but never shown
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
